Item
Old Army Black Powder Pistol, missing parts, see pictures. Selling for family of friend who passed recently. Asking $100 /offer. Will list other black powder arms as time permits.
Thanks for looking.
Contact Info
Price
Asking $100 but will consider offers.
Item...
I had good luck with using mineral spirits to remove the lube from some cast bullets when I first started my powder-coating. Took a little work and time to get them clean, but had no problem with the powder coating process. I am not familiar with the Hytek method.
Pending... sold to Droshki. I had listed on FGT and never got any responses until I listed it here and he told me he had replied there.
I may have more soon.
Thanks!
SOLD! 22LR Winchester M22 and Remington Golden HP - Chipley
I have several boxes of bulk 22lr - M22 is 500 rnds or a partial of 400 rnds.
Also have Remington HP in 525 and 550 round boxes.
I will take .06 per round for the M22 (round nose) or .07 for the Remington, unless you take all...
SOLD! 22LR for sale - CCI quiet and Remington Thunderbolt - Near Chipley
I have a box of 500 Thunderbolt solid round nose - $35.00
Also 8 boxes of 50 of CCI Quiet - 710 FPS - $30.00. This will not cycle a semi-auto, but shoots fine otherwise.
I will meet in Chipley or elsewhere for a...
Two topics here that caught my interest. First on the Lee dies: I use Lee dies exclusively. The only problem I have had, and I have it on several calibers, is with the depriming, resizing die. This is the only die in the set which has too narrow "funnel" for the case to slide into. If it is...
Yes, no problem sizing to .356. I don't have very hard lead, just stuff I collected and some I bought off ebay. I would even try some at .355 but don't know where to find a sizer that size except special order.
On the powder coating, I like the chrome best. The first few batches I made...
I usually go to .358 for lead bullets. But yes, you could resize to .357. For my use, I think the powder coated bullets are equivalent to the fmj ones as far as loads and sizing goes. I have not done as much testing as I would like, but plan to in the near future. I was even thinking of...
CANCEL. I found what I NEEDED. I am looking for up to 500 cases of good used 7.62x39 brass. Will buy for the right price, or trade other caliber brass.
Thanks for the info. I happened to be in a gun shop today and there on display was a live 50BMG just like the ones I found, only it had been cleaned up a bit. I think I will just carefully clean these up and set them on my work bench out of normal reach.
I'm not sure if this is the correct place, but I found a couple of 50 cal live rounds in my dad's old stuff...must be wwII era.
I would like to display them but want them safe first. Obviously they won't fit in my inertia bullet puller.
Any suggestions on how to POSITIVELY make them safe...
SOLD...Soft point bullets for reloading 223 (.224 dia.) Chipley
I have approximately 2500 Hornady "look-alike" soft-point bullets which I bought in a group purchase, but never bought a rifle to use them. These are 55grain.
I will take $160.00 FTF or $175 shipped flat-rate. I prefer to sell...
Here are the pics or the loaded ammo. Second pic: On the left is the .358 rf 125gr resized to .356. On the right is the lee 125gr tc, also sized to .356. In the background are 40 s&w 180gr tc.
I finally got some time to reload some of the 9mm cast-powder-coated bullets as shown in my previous posts. I will post some pics soon of the loaded rounds.
I measured about 1115 fps from an EAA 4.5" barrel, using a load just under max for w231 with a 125g bullet. The bullets came out ot 128g...
The Eastwood Company. It's more expensive but much better quality than the Harbor freight stuff. I use the "shake and bake" method. Not perfect, but it works and doesn't waste the powder.
I recently received my Lee 125 RNFP mold and got some bullets cast and powder coated. I still have to find time to load and test them.
Here are some pics of the bullets after sizing to .357, along with some of 158g rnfp sized to .357.
I really like using the powder coated lead bullets...
You got my attention, so I just ordered one of the molds from Midway.
I have been casting some 358-158 RNFP and really like the way they look and perform. I will try these lighter ones and also size some for 9mm. BTW I have been powder-coating these recently instead of lubing.