DK Firearms

Barn Raising

The #1 community for Gun Owners of the Gulf Coast States

Member Benefits:

  • Fewer Ads!
  • Discuss all aspects of firearm ownership
  • Discuss anti-gun legislation
  • Buy, sell, and trade in the classified section
  • Chat with Local gun shops, ranges, trainers & other businesses
  • Discover free outdoor shooting areas
  • View up to date on firearm-related events
  • Share photos & video with other members
  • ...and so much more!
  • Jester896

    Master
    GCGF Supporter
    Rating - 100%
    9   0   0
    Joined
    May 14, 2017
    Messages
    2,533
    Points
    113
    Location
    SW GA
    Picked up some warehouse shelving and started on one 4X8 Table...Shit Brickhouse right there. Put the bottom shelf on the ground to keep stuff from rolling under. Bottom shelf will be lipped in case equipment vibrates something.
    Table.jpg
     

    Attachments

    • Table.jpg
      Table.jpg
      51.2 KB · Views: 211

    Big Shrek

    Marksman
    Rating - 0%
    0   0   0
    Joined
    Mar 4, 2016
    Messages
    986
    Points
    63
    Location
    Pensacola, FL
    Got the floors sealed...man that stuff is slick as Owl Shit.

    A/C guy couldn't shorten the lines so I buried them and hooked everything up today...WE GOT HEAT

    Living in Florida, and having seen record flooding over the last few years in several Southern States...
    have you considered putting that unit UP a little higher??
    Looks like you've got enough loose cable to boost it up a few feet and keep it out of Harm's Way :)
     

    Jester896

    Master
    GCGF Supporter
    Rating - 100%
    9   0   0
    Joined
    May 14, 2017
    Messages
    2,533
    Points
    113
    Location
    SW GA
    Got a little more completed. Back left 6' table will house the MEC and Dillon Loaders, my component rack also 6'...bullets on the top shelf...powder on the 2nd and maybe onto the 3rd...bottom for brass storage. Not sure if my tool box will stay there or the library will go there. Got the 4X8 work table completed...drill press..swagger..chop saw for 300BLK...sander...stuff like that on there. Storage underneath I think will be table saw, miter saw, and other items like that.

    tables.jpg

    you can see part of the top leaning against the wall where my single stage stuff will be.
     

    Attachments

    • tables.jpg
      tables.jpg
      48 KB · Views: 159

    Jester896

    Master
    GCGF Supporter
    Rating - 100%
    9   0   0
    Joined
    May 14, 2017
    Messages
    2,533
    Points
    113
    Location
    SW GA
    One step closer this afternoon. Had to move tool box for room constraints...put the Library there since it isn't so deep. That way when I install the bank under counter on the left end of larger than O originally though I would make (by 18") I can still get into the corner. The loading table ended up being 8'LX32"D and a finished height of 37". I will have to notch the 2X6 on the left side so the tool box will slide under and hope I left room under there for the fridge too. Right side will have a shelf/footrest maybe...things keep spinning about what is going where. There are shelves and additional cabinets in this somewhere too. I just might have to throw something away :wacko:

    IMG_2389.jpg

    I owe, I owe so off to work I go...maybe I will finish the loading bench after work this week.
     

    Attachments

    • IMG_2389.jpg
      IMG_2389.jpg
      31.3 KB · Views: 137

    Jester896

    Master
    GCGF Supporter
    Rating - 100%
    9   0   0
    Joined
    May 14, 2017
    Messages
    2,533
    Points
    113
    Location
    SW GA
    Piece By Piece
    IMG_0426.jpg
    a little junked up from moving some in...should look better after the weekend
     

    Attachments

    • IMG_0426.jpg
      IMG_0426.jpg
      62.3 KB · Views: 127

    Jester896

    Master
    GCGF Supporter
    Rating - 100%
    9   0   0
    Joined
    May 14, 2017
    Messages
    2,533
    Points
    113
    Location
    SW GA
    I just might be able to load a rifle round or 2 now

    IMG_2454.jpg
     

    Attachments

    • IMG_2454.jpg
      IMG_2454.jpg
      58 KB · Views: 94

    Snake-Eyes

    Master
    Rating - 100%
    2   0   0
    Joined
    Jun 22, 2013
    Messages
    3,416
    Points
    113
    Location
    Florida
    That looks GREAT. Thanks for taking the time to share the progress with us.
     

    Jester896

    Master
    GCGF Supporter
    Rating - 100%
    9   0   0
    Joined
    May 14, 2017
    Messages
    2,533
    Points
    113
    Location
    SW GA
    Moved and shelved bullets, primers, and powder today before I went to the WMA Range close by.
    Finished shelving up when I got back...looks like I will get to do powder 1 more time...found 5 more 8s and 4 1# in another spot.
    Primers are in the gray cabinet to the left of the loading bench.

    IMG_2470.jpg

    hope I can get these on the next shelf down and still get brass on it.

    IMG_2472_LI.jpg
     

    Attachments

    • IMG_2470.jpg
      IMG_2470.jpg
      60.8 KB · Views: 61
    • IMG_2472_LI.jpg
      IMG_2472_LI.jpg
      56.7 KB · Views: 62
    Top Bottom