Join GulfCoastGunForum For Free

Results 1 to 7 of 7
  1. #1
    50 CAL Red's Avatar
    Join Date
    May 2016
    Location
    Crestview
    Posts
    2,089

    AR15 gas tube pinch?

    Hi guys,
    I have a Colt 6920 that seems to have tiny cant one way which is pinching the gas tube a bit and if you look very close, OCD close, you can see even the handguard is ever so slightly canted to one side.

    So I am guessing the main problem lies with the barrel nut? maybe too tight or not tight enough? I have a wrench but could not get it to budge in either direction. I took it in to a gunsmith and was told that it is well within spec and is nothing out of the ordinary.

    For what its worth, there is no binding anywhere and it has never jammed on me, and I have put over 1k thru it without issue. It cycles smooth and is accurate. I just have noticed on the majority of military issue M4s that there is actually a tiny bit of wobble on the gas tube on the inside of the upper and the rails always line up true.

    Its perfectly functioning as it is but I am a bit OCD when it comes to little things like this so please tell me AR gurus. What should I do? I can my old Colt to have the little gas tube wiggle and I want my handguards perfectly inline with the upper.

    Please gents, any advice would be greatly appreciated. Should I take out the tube and attempt to line up the barrel nut? I am at a loss on this one. Help gents....
    Thanks in advance.


  2. #2
    Local Dealer Little Jack's Guns's Avatar
    Join Date
    Sep 2012
    Location
    Milton
    Posts
    3,225
    If it works, don't mess it up.
    Intentionally Left Blank.... Or is it?

  3. 4 Like Little Jack's Guns's Post:


  4. #3
    Super Moderator JWlineman's Avatar
    Join Date
    Oct 2012
    Location
    Pensacola
    Posts
    5,803
    Quote Originally Posted by Little Jack's Guns View Post
    If it works, don't mess it up.
    Ditto

    Sent from my SM-N950U using Tapatalk
    --Insert inspirational quote here--

  5. Likes JWlineman's Post:


  6. #4
    50 CAL Red's Avatar
    Join Date
    May 2016
    Location
    Crestview
    Posts
    2,089
    lol but the slight cant of the handguards lol. I have CAR15 plastic on there now but I had rails on there and you could really tell. Its just the OCD in me I suppose.

  7. #5
    45 ACP FNHman's Avatar
    Join Date
    Jan 2013
    Location
    Cantonment FL
    Posts
    447
    As I read your post I'm a little confused, doesnt the colt 6920 have 2 piece plastic hand guards. If so, wouldn't the problem be the front site pinning or incorrect barrel extension pinning that causes the rotation issue? I always wondered if they drilled the gas hole after the barrel extension pinning or before cause I've seen a few aftermarket barrels that were a few degrees off in relation to the gas block hole. Or maybe it has a perfect gas block hole to barrel extension pinning and the issue is the front site was pinned slightly canted?

    If you have an aftermarket barrel nut and a free floating hand guard disregard the above.

  8. #6
    Super Moderator donr101395's Avatar
    Join Date
    Jan 2013
    Location
    Crestview
    Posts
    2,298
    If the handguards are canted the FSB is canted.

  9. Likes donr101395's Post:

    FLT

  10. #7
    45 ACP Army_of_One's Avatar
    Join Date
    Nov 2012
    Location
    Fort Walton Beach
    Posts
    116
    Have you ever tried removing the flash hider?

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •